Send Email
Send SMS
Search
Saif Trading Corporation


Dr. Fixit Products

Leading Wholesale Trader of dr. fixit 131 bathseal 2k, dr. fixit newcoat ezee, dr. fixit 602 heatshield, dr. fixit 601 raincoat, dr. fixit 217 crack-x shrinkfree and dr. fixit 112 pidifin 2k from Chennai.

Dr. Fixit 131 Bathseal 2K

REQUEST CALLBACK

Dr. Fixit 131 Bathseal 2K
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 400 / OnwardsGet Latest Price

Product Details:
BrandDr Fixit
Model131 Bathseal 2K
Available Packing3 & 15 kg
Nature and Type2 component (1 part polymer &2 part powder)
Wet Density of the Mix1.65 - 1.75
pH of the Mix10.0 - 12.0
Pot Life of the Mix40 - 45 @30 deg C in minutes
Elongation at Break at DFT50-60% of 1 mm
Water PermeabilityExcellent - no leakage observed after 24 hrs

Description:
  • Dr. Fixit 131 Bathseal 2K is a two-component cementitious, polymer modified elastomeric, waterproofing coating composed of cement, properly selected & graded aggregates, additives & acrylic emulsion polymer as a binder. It is applied to waterproof and protect concrete and masonry substrates, typically in wet areas such as bathrooms, kitchen sinks, etc.

Areas of Application:
  • Dr. Fixit 131 Bathseal 2K must be applied to new or old concrete substrates that are structurally sound and properly levelled.
  • Sunken portion of bathroom & toilet

Features & Benefits:
  • Elastomeric elastomeric flexible coating that accommodate cracks up to 2 mm with an elasticity of 40-50%
  • Low water permeability excellent resistance to ingress of water
  • Adhesion excellent adhesion to concrete and masonry surfaces
  • User friendly Ease of application by brush or roller

MIXing:
  • Shake the liquid component well to a homogenous milky colour.
  • Always add powder to polymer under constant stirring using slow speed paddle mixer to achieve smooth and homogeneous slurry.
  • Allow to stand for about 5 mins to release entrapped airFor new bathrooms.

Application of Dr. Fixit Bathseal 2k:
  • Apply first coat of Dr Fixit Bathseal 2K all over the floor surface in bathroom extending on side walls up to 1 m height covering the angle fillet.
  • While the coating is still wet place the glass fibre mesh (2.5 mm x2.5 mm) on the angle fillet extending about 50 mm on floor surface and 50 mm on walls and allow it to soak completely with material.
  • Before the coating dries apply immediately another coat of Dr. Fixit Bathseal 2K only on the angle fillet completely covering the mesh thus embedding it firmly between two coats of Dr. Fixit Bathseal 2K.
  • Allow the coating to dry completely for 6 to 8 hrs before applying second coat all over the floor area and walls. The angle fillet area now has three coats of Dr. Fixit Bathseal 2K with mesh embedded firmly within the coating.
  • Allow the coating to dry completely for 3-4 days. Do not cure with water but keep coating moist using wet hessian cloth.
  • Test the efficacy of the coating by conducting ponding test after complete cure after 3-4 days.
  • For this pond water up to 50-75 mm in sunken portion for 24 hrs and check for effectiveness of waterproofing.
  • After this lay cement sand screed or brick bat coba, as the case may be, taking care all the time that the coating does not get damaged during this activity.

Precautions & Limitations:
  • Do not part mix. Mix the entire quantity of both the components at one go.
  • Do not dilute with water.
  • Always add powder to liquid to avoid lump formation.
  • Do not cure by flooding with water.
  • Cure the membrane with a moist hessian cloth
  • Do not conduct any ponding test before it is completely cured .

Coverage:
  • Approximately 0.6 – 0.75 m2 / kg at 1 mm thickness in 2 coats, depending on the level of the substrate.

Shelf Life & Storage:
  • Shelf life is 12 months from the date of manufacturing.
  • Store in shed, protecting from direct sunlight and away from extreme temperature.
  • In extremely hot temperature conditions, store in a temperature-controlled environment i.e. less than 300C.

Health & Safety Precautions:
  • Dr. Fixit 131 Bathseal 2K is alkaline and should not come into contact with skin or eyes. Avoid inhalation of dust during mixing.
  • Gloves, goggles and dust masks should be worn, during mixing and handling the product.
  • Any contact to eyes should be washed immediately with clean water and seek medical advice
    Yes! I am interested

    View PDF

    Dr. Fixit Newcoat Ezee

    REQUEST CALLBACK

    Dr. Fixit Newcoat Ezee
    Get Best Quote

    Thanks for Contacting Us.

    Approx. Rs 400 / OnwardsGet Latest Price

    Product Details:
    Water AbsorptionMore than 20 ASTM D471
    BrandDr Fixit
    Available Packaging4 & 20 litres
    Theoretical Coverage2.25 sq.mtrs. per litre per coat. Two coats are recommended.
    Solid Content55 % (w/w) TGA /DTA Analyser
    Elongation at Break100% ASTM D 412 2002
    Adhesion Strength1.0 N/mm2 ASTM D 4541 2002
    Crack BridgingNo cracks up to 1 mm ASTM C 836 1995
    Hydrostatic Pressure7 Bar Passes DIN 1048
    Water Ponding TestNo water penetration through the coating layer
    Tensile Strength1.0 N/mm2 ASTM D 412 2002

    Description:
    • Dr. Fixit Newcoat Ezee is an elastomeric waterproof coating that provides a seamless and tough waterproof barrier with excellent crack bridging ability that can accommodate movements due to thermal variations in the waterproofing system.

    Features:
    • Waterproofing: Provides excellent water resistant barrier on roof / terrace
    • Tough and abrasion resistant: Suitable for light foot traffic
    • Highly durable and light weight: UV resistant and needs no extra protective screed
    • Flexible and elastic: Accommodates movements in waterproofing system and covers and bridges hairline cracks
    • Easy to apply: No need to remove the existing system. Can be brush or roller applied on vertical surfaces without sagging.

    Typical Applications:
    • Building Roofs / Terraces – Flat & Slope.
    • Over existing cementitious waterproofing treatments like sound brick-bat coba, concrete screeds, acrylic coatings, etc.

    Method of Application:
    Surface Preparation:
    • Prepare the surface thoroughly by cleaning, washing and removing dust, dirt, oil, grease and loose particles.
    • Ensure that the roof slope is a minimum of 1 in 100 to enable water run off.
    • In existing old terraces such as brick-bat-coba or screeds, the substrate must be checked for its soundness. Damaged or hollow portions, sharp edges, etc. must be cut and repaired with a polymer-modified mortar using Dr. Fixit Pidicrete URP.
    • Bitumen based waterproofing treatments must be completely removed by mechanical scarification or by any other effective mechanical means.

    Application:
    • Apply one coat of Dr. Fixit Primeseal (diluted with water in the ratio 2:1) at the rate of 100-110 sq ft/ liter. Allow it to dry for 2-3 hours.
    • Apply the first coat of Dr. Fixit Newcoat Ezee at the rate of 2.25 sq.mtrs per litre and allow it to dry before taking up the second coat, the rate of application being the same. This would ensure correct consumption of material that will deliver a total DFT of 500 – 600 micron.
    • Minimum drying time between coats will be 4 to 6 hours.
    • Allow the system to air cure for 7 days minimum. To achieve the full proof waterproofing, all parapet walls should be covered with Newcoat Ezee.
    • All wall to floor joints must be provided with proper angle fillets prepared with polymer modified mortar using
    • Dr. Fixit Pidicrete URP.
    • If the surface has excess moisture then there is possibility of blister formation in case of all liquid applied membrane coatings

    Precautions & Limitations:
    • All corners, gaps, joints, protrusions & outlets shall be coated with extra coat.
    • Do not apply during rains.
    • Substrate MUST be in SSD condition for application of primer.
    • The product is designed only for foot traffic and not vehicular or movement of machinery or equipments.

    Shelf Life:
    • Shelf life is 24 months from the date of manufacturing if stored in original and unopened packaging in a cool dry place away from direct sunlight.

    Health & Safety:
    • Skin Contact: Wash skin with soap & water. Remove contaminated clothes.
    • On eye contact: Immediately splash eyes with plenty of water. Consult Physician if irritation persists.
    • Ingestion: It is based on Water Based Coating system, however, seek medical help.
    Yes! I am interested

    View PDF

    Dr. Fixit 602 Heatshield

    REQUEST CALLBACK

    Dr. Fixit 602 Heatshield
    Get Best Quote

    Thanks for Contacting Us.

    Approx. Rs 400 / OnwardsGet Latest Price

    Product Details:
    BrandDr Fixit
    Model602
    StandardConforms to ASTM E-903
    Available Packing1, 4 and 20 litre
    Solid ContentMore than 60 % ASTM D 1010
    Thermal Conductivity0.029 w/mK
    Abrasion ResistanceNo wear after 450 litres of falling sand ASTM D 968
    Wind Driven Rain ResistanceTTC - 555 No moisture penetration after 24 hours.
    Total Solar Energy Rejected94 %
    SRI Value83.8% ASTM E-903
    Accelerated WeatheringPass (2000 Hrs) ASTM D 4587
    Relative Heat Gain30 Btu/hr/sq.ft
    AppearanceFree flowing, homogeneous & uniform paste.
    ColorWhite
    Specific Gravity1.01
    Elongation200 % ASTM D 412
    Tensile Strength0.276 @ 25 deg C, N/mm2 ASTM D 412

    Description:
    • Dr. Fixit 602 Heatshield is a heat reducing & ‘Energy Saving’ elastomeric coating composed of acrylic emulsion polymers, microspheres, properly selected & graded inert fillers, light fast & weather durable white pigments, additives & water as medium. It is used as a heat insulating coating on building rooftops & exterior walls because it helps in reducing power consumption substantially by reducing the load on air-conditioners & keeps the interiors cool with additional function of waterproofing.
    • Dr. Fixit Heatshield contains advanced material of ‘Hollow Micro spheres based on Borosilicate Glass as micro bubbles’ having remarkable ‘Heat Insulation’ property. The unique spherical shape of the glass bubble produces stable voids which results in low thermal conductivity and a low dielectric constant. When applied on substrate, the hollow micro spheres form a closely packed structure like ‘Air Space’ within the dry film layer that serves as insulation medium to resist heat transfer. Dr. Fixit Heatshield has thus the ability to slow down heat transfer remarkably and keep interiors of externally coated surface of a building cooler by re-radiating most of the solar heat back into the atmosphere.

    Areas of Application:
    • Terraces and rooftops of buildings - cementitious, asbestos & metal surfaces
    • Industrial & godown shades with GI or asbestos roofs
    • Exterior walls of buildings
    • Cold storages, computer server rooms, electrical control panel rooms, etc
    • Metal & concrete storage tanks for water, chemicals and fuel in petrochemical industry

    Features & Benefits:
    • Heat Insulation: Reduces the conductivity of heat from exterior to interior, thus lowers the temperature.
    • Solar Reflectance: 83.8% solar reflectance ( ASTM E-903 ), re-radiated heat back to atmosphere
    • UV and IR resistant: Resistance to UV & IR emission, protects coating from damage and reduces heat conductivity.
    • Microbial resistant: Resistance to algae and fungus growth results into lesser maintenance.
    • Non-Toxic water based system: Eco friendly
    • Energy Saving: Reduction in electrical consumption for air-conditioners, saves energy cost

    Method of Application:
    • Surface Preparation: on Cementitious Surfaces
    • Surface to be applied upon must be free from dust, loose material, paint, oil, or any other material which may impair adhesion
    • Mechanical means such as wire brushing & shot blasting can be used. Finally vacuum cleaning of all loose solids and liquids can be done if required
    • All surface cracks up to 5 mm width should be filled up with Dr. Fixit Crack X or Dr. Fixit Unifiller.
    • Cracks more than 5 mm and all separation gaps should be filled up with Dr. Fixit Pidicrete URP or Dr. Fixit Unibond SBR modified mortar or as specified.

    Precautions & Limitations:
    • Do not dilute.
    • Always to be kept as final coat. i.e. No overcoating on Dr. Fixit Heatshield

    Shelf Life & Storage:
    • Shelf life is 24 months from the date of manufacturing. Store in a cool & dry place.
    • Keep away from direct sun light.

    Health & Safety Precautions:
    • Skin Contact: Wash skin with soap & water. Remove contaminated clothes.
    • On eye contact: Immediately splash eyes with plenty of water. Consult Physician if irritation persists.
    • Ingestion: Do not induce vomiting. Never give anything by mouth to an unconscious person. Call a Physician.
    Yes! I am interested

    View PDF

    Dr. Fixit 601 Raincoat

    REQUEST CALLBACK

    Dr. Fixit 601 Raincoat
    Get Best Quote

    Thanks for Contacting Us.

    Approx. Rs 400 / OnwardsGet Latest Price

    Product Details:
    Available PackagingWhite Base - 1, 4 & 20 litre, Mid Tone and Dark Base - 900 ml, 3.8 & 19 litre
    NatureSingle component
    PH8.0 - 9.0
    Solid Content55.0 - 58.0 %
    Water Permeability6 Depth of water penetration BS EN 12390
    Reduction in Water Penetration68%
    Rapid Chloride Penetration TestVery low ASTM C 1202 - 97, Penetration of chloride ion
    Accelerated WeatheringNo defects (2000 hrs UV exposure) ASTM D 4587
    Adhesion Strength1 N/mm2 ASTM D 4541
    Coating Thickness110 (2 coats DFT), microns
    Carbon Dioxide Diffusion Equivalent Air Layer Thickness Meter55.3 DIN EN 1062-62002
    Specific Gravity1.31 - 1.35
    BrandDr Fixit
    Tensile Strength1.5 N/mm2 ASTM D 412-02
    AppearanceEmulsion (available in White, dark and mid-tone bases)
    Model601
    ElongationMin 100% ASTM D 412-02

    Dr. Fixit 601 Raincoat is composed of high quality acrylic emulsion polymer, uv resistant & weather durable pigments, properly selected & graded fine fillers, additives & biocides. It is used as a waterproofing & protective coating for exterior walls of the buildings.

    Features:
    • Flexibility: Flexible and covers hairline cracks (up to 0.5 mm) effectively, thus prevents ingress of water.
    • Toughness: Tough film withstands wind driven rain.
    • Ready to use: No dilution is required.
    • Microbial resistance: Resistance to fungus and algae hence maintains the aesthetic value.
    • UV resistant: Resistance to UV hence coating has longer life.
    • Low dirt pick up: Very low dirt pick up & can be cleaned easily hence maintains the aesthetics.
    • Breathability: Permeable to water vapour.
    • Ease of application: User friendly, easily applicable by brush, roller or spray.
    • Non toxic: It is Eco friendly.

    Typical Application:
    • All types of exterior masonry surfaces, concrete, cement sand renderings, etc.
    • Applicable on asbestos sheets.
    • As an anti carbonation coating for concrete structures

    Method of Application:Surface Perparation:
    • All new cement-sand renderings /concrete surfaces should be allowed to age minimum 28 days before surface coating.
    • Surface for treatment must be thoroughly cleaned of all laitance, loose material, oil, grease, etc. by mechanical means such as wire brushing.
    • All surface cracks up to 5 mm width should be filled up with Dr. Fixit Crack-X. Cracks more than 5 mm and all separation gaps should be filled up with Dr. Fixit Pidicrete URP modified mortar or as specified.

    Priming:
    • Prime the surface with Dr. Fixit Primeseal diluted with potable water by volume in 2:1 ratio (2 parts primer and 1
    • part water) and allow it to dry for 2 to 3 hours

    Application:
    • Use Dr. Fixit Raincoat directly from the container. Stir contents well before use.
    • Apply two coats of Dr. Fixit Raincoat without dilution by brush or roller at a time interval of 5-6 hours.
    • For enhanced protection, apply additional coat of Dr. Fixit Raincoat on rain lashing walls, chajjas and parapet walls.

    Precautions & Limitations:
    • Do not dilute Dr. Fixit Raincoat.
    • Recommended to be primed with Dr. Fixit Primeseal only.
    • Do not apply when ambient temperature is below 100C or above 350C.
    • Do not apply in direct sunlight or during rains.
    • Adhesion property may get affected over putty and very smooth surfaces.
    • Mid tone base & Dark base shall not be applied directly as tinting is must for formulating shades.
    • If the surface has excess moisture then there is possibility of blister formation in case of all liquid applie membrane coatings.

    Theoretical Coverage:
    • 3.0 to 3.5 m2 per litre for 2 coats *Coverage may vary depending upon the texture and porosity of the surface

    Shelf Life:
    • Shelf life is 36 months from the date of manufacturing if stored in original and unopened packaging in a cool dry place away from direct sunlight.

    Health & Safety:
    • Skin Contact: Wash skin with soap & water. Remove contaminated clothes.
    • On eye contact: Immediately splash eyes with plenty of water. Consult Physician if irritation persists.
    • Ingestion: Do not induce vomiting. Never give anything by mouth to an unconscious person. Call a Physician.

    Yes! I am interested

    View PDF

    Dr. Fixit 217 Crack-X Shrinkfree

    REQUEST CALLBACK

    Dr. Fixit 217 Crack-X Shrinkfree
    Get Best Quote

    Thanks for Contacting Us.

    Approx. Rs 400 / OnwardsGet Latest Price

    Product Details:
    BrandDr Fixit
    Model217 Crack-X
    Coverage30-34 running meter per ltr for a depth & width of 5 mm
    Packaging1 ltr.
    BaseAcrylic with specially added fillers
    Drying Time5 - 6 @ 30 deg C, hrs
    Full Curing Time7 days @ 30 deg C
    AppearanceWhite paste
    Specific Gravity0.0.26 +/-0.02

    Dr. Fixit 217 Crack-X Shrinkfree is composed of quality polymers, select fillers & additives. It is fast drying and flexible, light weight, putty like material used for filling cracks in plastered surfaces. It is 100% shrink-free, water resistant after drying & bonds strongly to cementitious substrates

    Features & Benefits:
    • Shrinkage: Non-shrink even after curing, prevents from cohesive & adhesive failure on exposure.
    • Application applied as one time filling (does not require second time application, as required in other acrylic sealants).
    • User friendlyOne pack, very soft paste, easily applicable by fingers or putty knife.
    • Saggingnon-sag nature helps in filling of vertical & overhead cracks.
    • Sandingno sanding is required.
    • StainingDoes not migrate any liquid component into concrete surface thus prevents staining.
    • Adhesionexcellent adhesion to cementitious surfaces prevents water leakages through the cracks.
    • DurabilityUV & weather resistance properties increases the life expectancy of the surface.
    • Non-toxicit is non-toxic hence user friendly
    • Paintabilityeasily paintable after 5-6 hours of application.

    Method of Application:Surface Preparation:
    • Surface must be free from dust, oil, grease, and loose particles, etc. moisten the surface before applying Dr. fixit Crack-X Shrinkfree.
    • fine hairline cracks must be widened upto 1 mm minimum and then filled.
    • for filling Dr. fixit Crack-X Shrinkfree on the internal surfaces, existing POP or painter’s putty must be removed till plaster surface is exposed.

    Application:
    • Press Dr. fixit Crack-X Shrinkfree firmly into the crack One time OnlY with a spatula or putty knife and level the surface.
    • handball application can also be used as per the convenience.
    • Care must be taken to avoid formation of cavities or bubbles during application.
    • allow it to dry in ambient conditions for 5-6 hrs before painting. for best results 7 days air curing is advised.
    • further POP or painters putty application can be taken up once it is fully dry.

    Cleaning:
    • Clean tools & equipments by soap & water. Wash hands with soap & warm water.

    Precautions & limitations:
    • Not for cracks in POP or painter’s putty.
    • Not recommended to use under the rain.
    • Not meant for structural cracks in concrete, slab, construction joints.
    • Jet or Power washing on walls not advisable prior to application.
    • During application below 10°C, drying time will be delayed.
    • Container to be tightly closed after application. if filler compound becomes too dry, add potable water in ratio of 1 teaspoon in 250 ml of Dr. fixit Crack-X Shrinkfree.

    Shelf life & Storage:
    • Shelf life is 12 months from the date of manufacturing. Store in cool & dry place, away from sun light.

    Health & Safety Precautions:
    • as with all chemical products, caution should always be exercised.
    • Protective clothings, such as gloves and goggles, should be worn (see packaging for specific instructions).
    • treat any contact to the skin or eyes with fresh water immediately.
    • Should any of the products be accidentally swallowed, do not induce vomiting but call for medical assistance immediately.
    • ensure the container is available for the medical attendant to examine any relevant instructions and contents details. reseal all containers after use and ensure product is stored as instructed on the safety section of the labelling.

    Yes! I am interested

    View PDF

    Dr. Fixit 112 Pidifin 2K

    REQUEST CALLBACK

    Dr. Fixit 112 Pidifin 2K
    Get Best Quote

    Thanks for Contacting Us.

    Approx. Rs 400 / OnwardsGet Latest Price

    Product Details:
    Available Packing3 & 15 kg
    Nature and Type2 component (1 part polymer &2 part powder)
    Wet Density of the Mix1.65 - 1.75
    pH of the Mix10.0 - 12.0
    Pot Life of the Mix40 - 45 @30 deg C in minutes
    Elongation at Break at DFT50-60% of 1 mm
    Water PermeabilityExcellent no leakage observed after 24 hrs
    BrandDr Fixit
    Model112 Pidifin 2K

    Description:
    • Dr. Fixit 112 Pidifin 2K is a acrylic cementitious, polymer modified elastomeric, waterproofing & protective coating composed of best quality Portland cement, properly selected & graded aggregates, additives & acrylic emulsion polymer as a binder. It is applied to waterproof and protect concrete and masonry substrates.

    Features & Benefits:
    • Elastomeric: Elastomeric flexible coating that accommodate cracks up to 2 mm with an elasticity of 40-50%
    • Low water permeability: Excellent resistance to ingress of water
    • Adhesion: Excellent adhesion to concrete and masonry surfaces
    • Eco-friendly: Non-toxic with low VOC content
    • CFTRI certified: As a “potable water safe” coating for waterproofing for water tanks

    Areas of Application:
    • Dr. Fixit 112 Pidifin 2K must be applied to new or old concrete substrates that are structurally sound.
    • Excellent as a waterproof coating for bathrooms, kitchen sinks, balconies, etc.
    • Ideal as a coating for waterproofing of chhajjas, canopies, etc.
    • As waterproof coating on internal sides of domestic water tanks.
    • Good for waterproofing of sloped roofs.
    • As a waterproof coating for terraces of areas up to 100-150 m2

    Method of Application:Surface Preparation:
    • The surface of application must be thoroughly prepared by mechanical means, to remove all loose particles, laitance, etc.
    • Oil and grease, if any, must be de-greased with suitable solvents. It then must be washed off with jet of water and brought to touch dry state. Any surface undulations, cracks and crevices must be duly filled or repaired with cement sand mortar mixed with latex polymers such as Dr. Fixit Pidicrete URP / Dr. Fixit Pidicrete MPB.

    Mixing:
    • Shake the liquid component well to a homogenous milky colour.
    • Use heavy duty slow speed mechanical mixer fitted with a suitable paddle for mixing the two components of the material.
    • In a mixing vessel, slowly add the powder component in to the liquid under continuous stirring. Continue to stir thoroughly to achieve a lump free homogenous slurry.

    Coverage:
    • Approximately 0.6 – 0.75 m2 / kg at 1 mm thickness in 2 coats, depending on the level of the substrate.

    Precautions & Limitations:
    • Do not part mix. Mix the entire quantity of both the components at one go.
    • Do not dilute.
    • Always add powder to liquid to avoid lump formation.
    • Do not cure by flooding with water.
    • Cure the membrane with moist hessian cloths
    • Do not conduct any ponding test before it is completely cured for 7 days
    • Always protect the membrane with screed in areas exposed to foot and other traffic

    Shelf Life & Storage:
    • Shelf life is 12 months from the date of manufacturing.
    • Store in shed, protecting from direct sunlight and away from extreme temperature.
    • In extremely hot temperature conditions, store in a temperature-controlled environment i.e. less than 300C.

    Health & Safety Precautions:
    • Dr. Fixit Pidifin 2K is alkaline and should not come into contact with skin or eyes.
    • Avoid inhalation of dust during mixing.
    • Gloves, goggles and dust masks should be worn, during mixing and handling the product.
    • Any contact to eyes should be washed immediately with clean water and seek medical advice
    Yes! I am interested

    View PDF

    Dr. Fixit 148 RoofSeal

    REQUEST CALLBACK

    Dr. Fixit 148 RoofSeal
    Get Best Quote

    Thanks for Contacting Us.

    Approx. Rs 400 / OnwardsGet Latest Price

    Product Details:
    Available Packing5 & 20 Ltrs
    Hardness Shore AMore than 50 ASTM D2240 91
    Water PenetrationNo penetration @ 3 bar DIN 1048 Pt 5 91
    Brush AbilityNo sag, slip & run off
    Solid Content55-60 % ASTM D 1644
    Elongation at BreakMore than 500 % ASTM D-412
    Water ResistantNo blistering and re-emulsification ASTM D-870
    Film Thickness700-750 micron in two coats
    Peel Adhesion to Concrete1.5 N / mm2 ASTM D
    Water Vapour Permeability0-5 gm/sqm. 24 hrs. (Full cured in 24 hrs.) IS 7809 / 1977
    Crack BridgingNo crack at 2 mm gap ASTM C836 00
    Specific Gravity0.99 -1.05
    Water Absorption0.02% ASTM D-642
    Coverage0.75 ltrs/ m2 / coat *Coverage may vary depending upon the texture and porosity of the surface
    BrandDr Fixit
    Model148 RoofSeal

    Description:
    • Dr. Fixit 148 RoofSeal is a single component cold applied elastomeric waterproofing coating based on synthetic resin emulsion. It is a tough yet extremely flexible coating that can be efficiently applied to any thickness by roller or squeegee creating a fully adhered waterproofing coating with no wastage. It is water based with low VOC’s that is sustainable for years as a waterproofing coating.

    Areas of Application:
    • Waterproofing of flat concrete roofs
    • As an external protective coating for block works before fixing Aluminum Composite Panels

    Method of Application:
    • Surface Preparation: Surface preparation is generally limited to cleaning by broom brush or compressed air. All surfaces to be applied must be free from dust, loose material, oil, or any other material which may impair adhesion of the material. All surface cracks up to 5 mm wide should be filled up with the same material and pre-striped prior to application of the material. All joints of vertical up stand should have 50 x 50 mm angle fillets prepared with sand -cement mortar; mixed with Dr. Fixit Pidicrete URP.
    • Primer: Primer is required only for high absorbent surface such as light weight concrete. Primer recommended to be used is Dr. Fixit Torchshield Primer, when the surface is completely dry

    Precautions & Limitations:
    • Careful supervision during application is needed, particularly in ensuring proper curing of concrete and consistent thickness
    • Apply Dr. Fixit Roofseal directly.
    • Always protect the coating with proper and appropriate screed.
    • Do not apply Dr. Fixit Roofseal directly in open sunlight when temperature is higher than 35oC.

    Shelf Life & Storage:
    • Shelf life is 12 months from the date of manufacturing in unopened condition. Store in cool and dry place. Keep away from direct sun light.

    Health & Safety Precautions:
    • During application wear protective clothing, gloves and eye goggles during application. Avoid product to contact eyes and skin.
    • Skin Contact: Wash immediately with plenty of clean water, use kerosene or mineral turpentine when the product has dried.
    • Eye contact: In the event of eye contact splash plenty of clean water immediately and seek medical advice.

    Water ponding test:
    • After full drying of second coat for at least 72 hrs, a water ponding test can be performed by filling water on the terrace by carefully blocking all the down take drain outlets without damaging the coating. The test shall be carried out for 48 hrs by filling water up to 50 mm level. Observe for leakages if any and then remove the water and allow the coating to dry completely for about 24 hrs before proceeding further.
    • Spread 100 grm/m2 geotextile over, before a concrete screed is laid. Protect the coating with a concrete screed in M 20 grade. The protective screed should be of minimum 50 mm thickness maintaining an average slope of 1:100 towards the drain outlets for effective and efficient draining of water. After the application of screed, provide control joints along the length and breadth of entire screed area. The joint can be provided by using a saw cutting machine attached with a 3 mm blade. The joints will be 12 mm wide and 12 mm deep. 28-30 days later, these joints can be filled with a suitable elastomeric sealant.
    Yes! I am interested

    View PDF

    Dr Fixit 101 LW Waterproofing Chemicals

    REQUEST CALLBACK

    Dr Fixit 101 LW  Waterproofing Chemicals
    • Dr Fixit 101 LW  Waterproofing Chemicals
    • Dr Fixit 101 LW  Waterproofing Chemicals
    Get Best Quote

    Thanks for Contacting Us.

    Approx. Rs 400 / OnwardsGet Latest Price

    Product Details:
    Non Volatile Content13.5 - 14.5%
    Dosage200 ml per 50 kg bag of cement
    Available Packing200 ml, 1, 5, 10, 20 & 100 litre
    Chloride ContentMax. 2.00% IS 2645 2003
    Water PermeabilityPasses IS 2645 2003
    Specific Gravity1.05 - 1.070 @ 25deg C
    pH Value9- 13
    AppearanceFree flowing liquid
    Compressive StrengthAs per the standard N /mm2 IS 2645 2003
    Model101 LW+
    Setting Time30 - 600 min. IS 2645 2003

    Dr Fixit 101 LW  Waterproofing Chemicals is specially formulated integral liquid waterproofing compound composed of surface active plasticising agents, polymers & additives. It is used as an additive for cement concrete, mortar & plasters. It makes concrete cohesive and prevents segregation.

    Standard Compliance / Specification:
    • Meets the requirements of IS : 2645-2003 and IS: 9103-2000 standards

    Areas of Application:
    • Waterproofing of concrete and sand-cement mortars used in
    • Basements,
    • Roof slabs and screeds,
    • Water tanks & water retaining structures,
    • External plastering,
    • Bathrooms and balconies,
    • Sumps and drains

    Features & Benefits:
    • Corrosion resistant: Makes concrete more cohesive, hence protects steel better against corrosion
    • Compatibility: Being a liquid, easily dispersible & compatible with concrete/mortar mixes.
    • Permeability: It reduces the permeability of water into concrete.
    • Strength: The setting time and compressive strength of the concrete remains within the specification limits.
    • Shrinkage: Reduces shrinkage crack development in plaster & concrete.
    • Workability: Improves workability of freshly mixed cement concrete.
    • Durability: Increases durability by improving waterproofing of concrete.

    Method of Application:
    • Charge cement & aggregates to concrete mixer as per the mix design, mix in dry state for 1–2 minutes.
    • Start addition of 75–80% mixing water & mix for 2-3 minutes.
    • Dr. Fixit Pidiproof LW+ is added as per the recommended dosage into the remaining mixing / gauging water,
    • then add to concrete mixer & mix for another 2 minutes.
    • Place the concrete or apply plaster, as needed.
    • Cure the applied mortar or concrete as per good construction practices.

    Precautions & Limitations:
    • Do not add Dr. Fixit Pidiproof LW+ directly to dry cement & aggregate mix.
    • Maintain water-cement ratio as low as possible.
    • Do not increase the dosage of Dr. Fixit Pidiproof LW+ than the recommendation

    Shelf Life & Storage:
    • Best before 2 years from the date manufacture when in sealed pack and stored under proper condition.
    • Store in a cool & dry place.

    Health & Safety Precautions:
    • Use rubber hand gloves & safety goggles, while using Dr. Fixit Pidiproof LW+.
    • In case of contact with skin, wash with plenty of water.
    • Keep out of reach of children

    Other Products Categories available:
    • Dr. Fixit brings you the widest range of Construction Chemicals
    Yes! I am interested

    View PDF

    Dr Fixit 301 Pidicrete URP

    REQUEST CALLBACK

    Dr Fixit 301 Pidicrete URP
    • Dr Fixit 301 Pidicrete URP
    • Dr Fixit 301 Pidicrete URP
    Get Best Quote

    Thanks for Contacting Us.

    Approx. Rs 400 / OnwardsGet Latest Price

    Product Details:
    NatureMilky white, translucent, free flowing liquid
    Total solids38+/-1 % by mass @ 105 deg C
    Specific Gravity1.01 at 27.5 deg C
    pH Value7.7
    Coverage2 -2.2 m2 for the mix of 1 kg of URP and 1.5 kg of cement
    BrandDr Fixit
    Packaging Size1 Kg, 5 Kg
    TypeSBR Latex- (Styrene Butadine Rubber latex)
    Model301

    Dr Fixit 301 Pidicrete URP is based on modified styrene butadiene latex supplied as a ready to use bonding agent in liquid consistency. It is used for repair of spalled concrete: floors, columns, beams, chhajas, slabs & waterproofing of toilets & bathrooms, small terraces etc. as it bonds strongly to old & new concrete and to plasters. It reduces shrinkage, prevents cracking, dust pick up & improves abrasion resistance.

    Standard Compliance / specification:
    • Meets the requirements of BS 6319 part 2:1983 & ASTM C 190-85 standards

    Areas of Application:
    • For concrete repairs - Spalled concrete of floors, columns, beams, chajja, slabs, parapets, etc.
    • For waterproofing: Small roof terraces, sunken portions of toilets & bathrooms, chajja & lift pits, balconies
    • As a bond coat: For bonding of new concrete to old concrete, masonry stone work, plastering
    • For cladding: Fixing or re-fixing of slip bricks, tiles, stones & marble bedding
    • As external rendering: Weatherproof & frost resistant render
    • As bonding slurry coat for pinhole treatment on concrete surface

    Features & Benefits:
    • Multipurpose: It is multipurpose & economical product, easy to use
    • Cracking: It prevents cracking by improving flexural strength
    • Hardness: Improves the hardness & prevents dust generation
    • Shrinkage: Reduces drying & aging shrinkage cracks
    • Bonding: Bond strongly to concrete, masonry, stonework, plasters, cementitious surfaces
    • Erosion & corrosion: Improves erosion resistance & prevents corrosion
    • Abrasion resistance: Improves abrasion resistance of the cement mix
    • Grouting: Reduces viscosity of cement injection grout for better fluidity & bonding

    Mix Design Using Dr. Fixit Pidicrete URP:
    S No.ApplicationCompositionQuantity of Dr. Fixit Pidicrete URPConsistency & thickness
    1Patching & repair mortarOPC – 50 kg Washed sand: 150 kg Water: 10 Lit6 -7.5 kgMortar consistency, 5-25 mm thickness
    2PCC/Floor ScreedOPC – 50 kg Graded & washed sand – 75 kg Coarse aggregates (6mm down size) - 75 kg Water – 10 Lit6 – 7.5 kgMortar consistency, 10-40 mm thickness
    3Waterproofing coatingOPC – 50 kg10 kgBrushable consistency
    4Bonding primerOPC – 50 kg15 kgBrushable consistency
    5Slurry for pin hole treatment & groutingOPC – 50 kg Water – 5 Lit5 kgSlurry consistency

    Dosage:
    • As a waterproofing coating: Mix proportion by volume; 1:1.5 (Dr. Fixit Pidicrete URP: Cement)
    • As a mortar modifier: 10-15 % of Dr. Fixit Pidicrete URP by weight of cement
    • As a bonding agent: Mix proportion by volume; 1:1 (Dr. Fixit Pidicrete URP: Cement)

    Coverage:
    • As a waterproofing coating: 22 – 25 sq.ft./kg in 2 coats
    • As a mortar modifier: 6-7.5 kg of Dr. Fixit Pidicrete URP per 50 kg of cement
    • As a bonding agent: 45 – 50 sq.ft./kg per coat


    Yes! I am interested

    View PDF

    Dr Fixit 603 Newcoat

    REQUEST CALLBACK

    Dr Fixit 603 Newcoat
    Get Best Quote

    Thanks for Contacting Us.

    Approx. Rs 400 / OnwardsGet Latest Price

    Product Details:
    Coverage2 m2 per litre per coat
    Model603
    Available Package Size4 & 20 litre
    Water Vapour Transmission19 g/m2 /day ASTM E 96 2000
    Algae and Fungus ResistantNo algae & fungus Growth (SS 345 1998)
    Crack BridgingNo cracks up to 2 mm width, No cracks up to 1 mm (10 cycles) ASTM C 836 1995
    Rapid Chloride PermeabilityVery low ASTM C 1202 - 97
    Water Permeability6 BS EN 12390, part 8 2000 (Depth of penetration at 5 bar pressure)
    Solid Content69 %
    Elongation at Break200 % ASTM D 412 2002
    UV Resistant AcceleratedExcellent No thermal degradation, ASTM G 154 2000
    WeatheringNo cracking, chalking and discoloration (1000 hours)
    Adhesion Strength0.9 N/mm2 ASTM D 4541 2002
    Hardness80 (Shore A) ASTM D 2240 2002
    Tensile Strength2.6 ASTM D 412 2002

    Dr Fixit 603 Newcoat is a heavy duty terrace waterproof coating system, composed of specially developed highly elastic & resilient acrylic polymers, properly selected & graded fillers, lightfast & weather durable pigments, micro-fibres, additives & best quality fungicidal in water medium. It is used as a liquid applied waterproofing membrane for all types of building terraces. Dr. Fixit Newcoat is a three-layer system with coats in different colours ensuring proper build-up of the thickness, making it a reliable waterproofing system. The coating performance can be enhanced
    for large roofs, by providing a fibre mesh that is embedded or sandwiched between the coats.

    Features & Benefits:
    • Film thickness: Provides higher dry film thickness of 1 to 1.25 mm in three coat application
    • Crack bridging: Bridges cracks up to 2 mm width
    • Application advantage - No need to remove existing sound brickbat coba, plaster, concrete surface
    • Suitability: Can be used for flat as well as sloping roofs
    • Strength: Higher tensile strength, tear resistance & bond strength with cementitious substrates
    • Resilience: Forms highly elastic & resilient coating so helps to withstand the structural movements
    • Durability: Resistant to UV & weather conditions
    • Abrasion resistant: No additional protective coating is required for roof subjected to foot traffic
    • Ease of application: Can be applied by brush & roller easily
    • Weight addition: Light in weight does not add extra weight over the roof
    • Toxicity: It is non-toxic in nature
    • Breathability: It is breathable
    • Easy to recoat existing surfaces coated earlier with Dr. Fixit Newcoat

    Method of Application:Surface Preparation:
    • Prepare the surface thoroughly by cleaning, washing and removing dust, dirt, oil, grease and loose particles.
    • In existing old terraces with brickbat coba or screeds, the substrate must be checked for its soundness.
    • Damaged or hollow portions, sharp edges, etc. must be cut and removed till the mother slab. The slab should be recoated with slurry of Dr. Fixit Pidicrete URP and cement in 1:1 proportion. After drying, the brick bat coba in that portion should be reinstated by mixing Dr. Fixit Pidicrete URP in the base slurry as well as while doing the top coba. In other areas, where the coba is sound, the surface cracks must be filled with Dr. Fixit. Crack-X or polymer-modified mortar in case cracks are wider than 5 mm.
    • Cracks less than 2 mm, should be cleaned free of dust with a vacuum cleaner.
    • Apply Dr. Fixit Primeseal in the crack and let it dry. Then pour Dr. Fixit Newcoat into these cracks and wait for it to dry.
    • Ensure that the roof slope of a minimum of 1 in 100, is already provided.

    Precautions & Limitations:
    • All corners, gaps, joints, protrusions & outlets shall be coated with two extra coats.
    • Do not apply during rains; substrate MUST be in SSD condition for application of primer.
    • The product is designed only for foot traffic and not vehicular or movement of machinery or equipment.
    • Do not apply Dr. Fixit Newcoat over expansion or moving joints
    • To achieve the full proof waterproofing, parapet walls should be covered with Dr. Fixit Raincoat
    • Never dilute Dr. Fixit Newcoat with water for ease of application

    Shelf Life & Storage:
    • Shelf life is 12 months from the date of manufacturing in unopened condition. Store in a cool & dry place.

    Health & Safety Precautions:

    • Skin Contact: Wash skin with soap & water. Remove contaminated clothes.
    • On eye contact: Immediately splash eyes with plenty of water. Consult Physician if irritation persists.
    Yes! I am interested

    View PDF

    Dr Fixit 201 Crack X Paste

    REQUEST CALLBACK

    Dr Fixit 201 Crack X Paste
    Get Best Quote

    Thanks for Contacting Us.

    Approx. Rs 400 / OnwardsGet Latest Price

    Product Details:
    Model201
    Service Temp Range-15 to + 80 deg C
    Extension RecoveryMin 75 ASTM C 736
    Freeze and Thaw stability and CyclesPasses 5
    Volume Shrinkage20 % ASTM C 1241
    Available Size200, 500 gms, 1 kg & 5 kg
    Special Gravity1.40 +/- 0.02 @ 30 deg C, gms/ml ASTM D 3800 - 79
    Movement Accommodation Factor+ 10 %
    Water resistanceExcellent
    ConsistencyViscous paste
    Non Volatile Content75 -80 % ASTM D 1010
    Tack Free Time30 - 40 % ASTM D 2377
    Vertical SlumpNi,l ASTM D 2202
    ColorWhite
    BrandDr Fixit

    Dr Fixit 201 Crack X Paste is composed of high quality weather durable acrylic emulsion polymer, properly selected graded fillers, light fast pigment& additives. It isa single pack, ready to use flexible putty for filling the cracks in plastered surfaces because it has excellent bonding, ease of application, water resistance, aesthetic appearance & durability.

    Specification:
    • Meets the requirements of ASTM C 834 – 91 standard.

    Areas of Application:
    • Internal & external Plastered brick masonry wall cracks of upto 5mm width.

    Features & Benefits:
    • Consistency: Paste form, without sagging.
    • Ease of application: Easy to apply by putty knife similar to conventional putties.
    • Flexibility: Flexible, therefore does not crack & accommodates minor movements in cracks.
    • VOC: Water based with very low voc hence eco-friendly.
    • Application advantage: Can be applied on damp surfaces but not on cracks with running water.
    • Paint ability:Over coatable by any type of polymer based paints, after 24 hours.
    • Staining: Non-staining.
    • Bonding: Excellent adhesion with cementitious surface.
    • Durability: Excellent resistance to UV & atmospheric conditions.
    • Tinting ability:It can be tinted using water-based stainers.
    • Toxicity: Non toxic & harmless to hands.

    Precautions & Limitations:
    • Should not be used for cracks more than 5 mm thick.
    • Not for application in cracks in structural members, expansion joints & separation gaps.
    • Not for cracks in POP or painter’s putty.
    • For application below 10oC, drying time will be delayed.
    • Container to be tightly closed after application.

    Cleaning:
    • Clean tools & equipments and hands with soap and warm water, immediately after use.

    Shelf Life & Storage:
    • Shelf life is 12 months from date of manufacturing in unopened containers.
    • Store at cool & dry place, away from sun heat.

    Coverage:
    • 25-30 running meter/kg (for a depth of 5mm and width of 5 mm).

    Health & Safety Precautions:
    • Use rubber hand gloves & safety goggles, while using Dr Fixit Crack X paste.
    • In case of contact with skin, wash with plenty of water.
    • Keep out of reach of children’s.
    • Should any of the products be accidentally swallowed do not induce omitting but call for medical assistance, immediately.

    Method of Application:
    Surface Preparation:
    • Surface must be free from dust, oil, grease, and loose particles etc. Moisten the surface before applying Dr. Fixit Crack-X Paste.
    • Fine hair line cracks must be widened up to 1 mm minimum by using scrapper and then filled
    • For filling Dr. Fixit Crack-X Paste on the internal surface, existing POP or painter’s putty must be removed till plaster surface is exposed.
    • For porous surfaces, apply primer coat prepared with Dr. Fixit Crack-X Paste and water in 1:1 proportion over the crack. Fill Dr. Fixit Crack-X Paste when the surface is tacky and not dried completely.

    Application:
    • Press Dr. Fixit Crack-X Paste firmly into the crack with a spatula or putty knifes and level with the surface.
    • Care must be taken to avoid formation of cavities or bubbles during application.
    • Allow it set for 24 hours and then apply another coat of Dr. Fixit Crack-X Paste.
    • Further POP or painter’s putty application can be taken up once it is fully dry.
    • For best results allow Dr. Fixit Crack-X Paste to cure for 7 days.
    Yes! I am interested

    View PDF
     
    X


    Explore More Products

    Contact via E-mail
    Contact via SMS
    Saif Trading Corporation
    Huzefa Raja (Proporiter)
    No. 52, Sembudoss Street , Parrys,
    Chennai - 600001, Tamil Nadu, India
    Call Us: 
    Call Response Rate: 50%
    Share Us :
    F G T L



    Home  |   About Us   |  Our Product Range  |  Site Map  |   Contact Us

    © Saif Trading Corporation. All Rights Reserved (Terms of Use)
    Developed and Managed by IndiaMART InterMESH Limited

    Saif Trading Corporation